Fixed Gas & Flame Detection

Gas Detectors

View all products
/
SMC 2001 Solid State Combustible Gas Detector

SMC 2001 Solid State Combustible Gas Detector

The SMC 2001 is a single-gas detector used to monitor combustible gas. The detector is based on solid-state technology, a simple and robust method of detection capable of detecting low parts-per-million (ppm) levels of gas. With the exception of periodic calibration to verify the alarm setting, no attention is required after installation.
Discontinued SMC 2350/2360 Telecom Gas Monitors

SMC 2350/2360 Telecom Gas Monitors

The SMC 2350/2360 Telecom Gas Monitors both continuously monitor for the presence of Carbon Monoxide (CO), but the Model 2360 also monitors for combustible gases. These hazardous gases are monitored in confined spaces in telecom sites, such as utility enclosures, to reduce the hazard of gas explosion and to maintain personnel safety.
Discontinued SMC 2400 Vault Gas Monitor

SMC 2400 Vault Gas Monitor

The SMC 2400 Vault Gas Monitor detects combustible and carbon monoxide gas leaks to reduce the hazard of gas explosion and to maintain personnel safety. The monitor offers the gas detection functions required by telecom site managers including uninterrupted power supply, long-life sensors, five alarm relays, and both audible and visual alarm indication.
Discontinued SMC 2450 Facility Environment Controller

SMC 2450 Facility Environment Controller

The SMC 2450 Facility Environment Controller is designed to manage HVAC controls, environmental alarms, and manage rigorous personnel safety requirements of controlled environment vaults (CEVs) and walk-in cabinets. The SMC 2450 also monitors CEVs for the presence of combustible and toxic gases and automatically initiates ventilation when an alarm threshold is exceeded.
/

Flame Detectors

View all products
TL105 Test Lamp

TL105 Test Lamp

The TL105 is a battery operated test lamp designed specifically to test General Monitors Flame Detectors. The TL105 is an explosion-proof test lamp that can be used with the FL4000H MSIR flame detector as well as any of the FL3100 Series Flame Detectors. The TL105 operates up to 35 feet from the flame detector.
/

Leak Detectors

View all products
Observer® i Ultrasonic Gas Leak Detector

Observer® i Ultrasonic Gas Leak Detector

Instantly detect pressurized gas leaks with this high-precision,  omni-direction acoustic detector utilizing Gassonic ultrasonic technology. Works even when traditional methods of gas detection are unsuitable or dependent on ventilation. Features Artificial Neural  Network (ANN) technology that distinguishes between real gas leaks and false  alarm sources without requiring any in-field training. The Observer® i UGLD provides an industry-leading detection range (up to 28 m) reducing the  number of detectors required. Ideal for use in complex, outdoor pipeline systems.
Discontinued Surveyor Ultrasonic Gas Leak Detector

Surveyor Ultrasonic Gas Leak Detector

The Surveyor detects gas leaks by sensing the airborne ultrasound emitted from leaking gas at high pressure. Ultrasonic gas detection is based on robust and proven Gassonic technology and designed for long and failsafe operation in extreme environmental conditions. Because the Surveyor responds to the source of a gas release rather than the dispersed gas, it is unaffected by changing wind directions, gas dilution, and the direction of the gas leak. Looking for an ultrasonic gas leak detector? Explore the many benefits of the Observer-i Ultrasonic Gas Detector.
/

Controllers

View all products
Discontinued MC600 Multi-Channel Controller

MC600 Multi-Channel Controller

The MC600 is a microprocessor-based multi-channel controller that provides six channels of continuous gas detection. It can be configured as either a local gas detection system, or it can be networked to provide a large plant-wide distributed safety system. It is compatible with our hydrocarbon sensors, H2S sensors, as well as our S4000CH, S4100C, S4000TH, S4100T, IR400, IR5500, IR700, TS4000H, Observer, and Surveyor gas detectors.
/

Fire & Gas Systems

View all products
Zero Two Series Gas and Flame Detection System

Zero Two Series Gas and Flame Detection System

Modular system offering the widest range of control cards for use in an integrated fire and/or gas detection system. The Zero Two Series system can monitor any combination of the following: combustible gas, H2S, toxic gas, ultrasonic, oxygen deficiency and flame detection. In addition, its open architecture allows the system to accommodate other sensing devices for tasks such as smoke detection, heat detection and manual call points. 
TA102A Single Channel Combustible Trip Amplifier Module

TA102A Single Channel Combustible Trip Amplifier Module

The TA102A is a single-channel Combustible Gas Trip Amplifier Module designed for use with one General Monitors intelligent transmitter to monitor combustible gases and vapors within the lower explosive limit (LEL) and provide status indication and alarm outputs. Microprocessor-based electronics allow all options to be user selectable through a front panel interface (mode / select switch and digital display). A digital display indicates fault codes and set up options. Other features include: LED indications of status, as well as both open collector and relay outputs for fault, low alarm and high alarm.
4802A Zero Two Series Control Module for Combustible Applications

4802A Zero Two Series Control Module for Combustible Applications

The 4802A is a single channel Combustible Gas Control Module that has been designed for use with General Monitors catalytic bead sensors. It is designed to monitor combustible gases and vapors within the lower explosive limit (LEL) and provide status indication and alarm outputs. Microprocessor-based electronics allow all options to be user selectable through the front panel interface. A digital display indicates gas concentration, fault codes, calibration cues and setup options. Other features: LED indications of status, as well as open collector and relay outputs.
/

Calibration Kits and Accessories

View all products
Ultima® Controller

Ultima® Controller

The Ultima Controller is purpose-designed and built to provide complete access to all advanced features of the Ultima and Ultima X Gas Monitors, as well as the Toxgard II Gas Monitor. Via its full-function and password-protected keypad, users can set the real time clock, set alarm levels, change span-gas values, display date of last calibration, display minimum, maximum and average gas values, change address and set future calibration time/date in addition to providing basic calibration functions.
SM5000 Sampling Module

SM5000 Sampling Module

Built for safety programs that demand gas concentration measurement before allowing entrance to an area, the SM5000 Sampling Module is exclusively designed to work with the Ultima X5000, Ultima XE and General Monitors S5000 gas monitors. The unit features an explosion-proof design and reliably extracts a sample from any confined or inaccessible area—or any area that is too hot, cold, or otherwise harsh—and delivers gas concentration reading directly to the installed gas monitor.
Catalytic Bead Sensors

Catalytic Bead Sensors

The General Monitors catalytic bead gas sensors are well known for their sensitivity, reliability and longevity and make them the first choice for most users of the catalytic oxidation gas detection principle. Every component is manufactured in-house to ensure optimum performance. Careful matching of the active and reference elements ("beads") result in a sensor that has negligible zero drift with respect to changes in humidity, pressure, and temperature.
/
Select up to 3 items to compare Compare (0)